[New product launch]

New window

Dongguan quansheng machinery equipment co., LTD. (hereinafter referred to as "quansheng machinery") printing machine dust collector qs-mc1727-96t is the latest product developed and produced, which has obtained the national appearance design patent and utility model patent. It is reported that quansheng machinery has been developing this product since 2010, and finally pushed the product into the market through continuous customer feedback and debugging and improvement.

Compared with the general dust collector, qs-mc1727-96t has the following characteristics:

1. It adopts new filter bag material, with high working temperature, high strength and long service life.

2. The product is suitable for the paper powder blown by the fan in the paper feeding department and printing department of various printing presses. When working, the dust cleaned from the dust collector bag falls directly into the collecting drawer for convenient cleaning.

3. Filter the particles containing dust and gas onto the bag fabric, so as to purify the gas.

4. Compared with the general dust collector, dust removal efficiency can be more than 99% stable, can remove about 1 micron particles. The precipitator has the advantages of simple structure, low investment cost, simple and reliable operation and low technical requirements for management and maintenance.

5. With a high (0.4 MPa - 7 MPa) pulse airflow blow to clear the dust on the filter a bian bag.

6. The duration and interval of the jet operation can be changed by adjusting the pulse cycle and pulse width, so as to keep the filter bag in a good filtering state. Therefore, the filter wind speed of the pulse bag filter is relatively high, and the dedusting effect is relatively stable. At the same time, the filter bag has no mechanical movement when the compressed air is blown back to clean the dust, and the service life of the filter bag is long.

7. The ventilation area of the new filter bag is increased by 60% compared with that of the general filter bag.

Industry value

The disadvantages of the old dust collector, the old dust removal equipment of the printing press used to use the primary filter bag, or simple filter cotton caused more than PM25 fine dust dispersed in the air, the filtering effect is poor, the production workshop dust, cleaning is not convenient.

Advantages of the new dust collector, to solve the old dust collector can not recover PM10 fine dust shortcomings, improve the production workshop working environment, to provide printing quality.

Customer case

Taiwan changsheng, Oriental seiko, zhuzhou sanxin, zhengzhou huaying packaging (ke shenglong), sundeli beer (bao wang) ding xin international group, guangzhou bingxin paper co., LTD., hangzhou bingxin paper co., LTD., Harbin bingxin paper co., LTD., shenyang bingxin paper co., LTD...

Technical parameters

Filter bag specifications: Φ 150 * 1450 * 1.9 mm

Filter bag material: Andrew CFC 300-500g anti-static polyester needled felt, heat setting, singling on one side, surface calendering dust easy to fall off, save cleaning time, by adding dual fiber to produce electrical conductivity.

Filter bag support frame material: galvanized snake dragon frame

Pulse solenoid valve specification: 1.5 inch Taiwan brand

Program control board :6~8 Taiwan brand

Operating temperature: ≤120℃

Rated pressure: 6~8Kg/cm2

Dust removal efficiency: 99%. It has been proved by experiments that it can deal with PM10 fine dust produced by most printing machines, greatly improving the air quality in the workshop.

Inlet dust concentration: ≤15g/m3

Filter wind speed: 0.5~2 m/min

Spray pressure: 0.5~0.7MPa

Pulse interval: adjustable from 1 to 60 seconds

Enterprise brief introduction

Quansheng machinery with sincere service, good reputation, dedicated to the vast number of cartons, printing, paper products and other industries to provide high quality, high technology supporting scrap paper recycling machinery equipment (that is, paper edge processing equipment) and various engineering services. At the same time, the company has a number of high-quality professional personnel, for the major manufacturers to provide product technical information and technical development guidance, pay more attention to product quality and quality service.

Chen zhiping, general manager of quansheng machinery, told the author that when choosing a printer dust collector, not only should pay attention to the air volume, but also should pay attention to the dust concentration. Because the performance of the filter and filter wind speed and gas dust concentration has a direct relationship. Through the filter bag, in general, the air velocity (i.e., filtration velocity) and the dust concentration of gas is inversely proportional to, therefore, when determining the filter area, also must satisfy the filter bag dust capacity (i.e., two ash removal during the lv bags are deposited on maximum allowable quantity per unit area) general dust capacity is not more than 400 g / ㎡, can press type calculation: gather dust = inlet gas dust concentration by filtering wind speed by two times of black ash time interval. If the calculated results exceed the dust collecting capacity, the filter wind speed should be reduced and the filter area should be increased to ensure that the dust collector can operate under normal conditions.